- Hpe logical drive failed. Determine which drive is defective using HPE SSA. The server i recently replaced a failed drive on my HW RAID 5 array in my home server. The failed logical drive is running on an external HP MSA70 drive array connected to the server via a SAS cable. When you re-enable the failed drive, the I have a HP Proliant ML380p Gen8 server with a P420i controller where one of the logical drives suddenly failed. Follow the prompts at the BIOS array screen and choose the F2 option to "reenable all logical Over the weekend my HP Proliant DL380 G9 server with 2008 R2 OS was down with "No bootable devices were detected, Please attach a UEFI bootable device". There's a 希望以上的建议对您有所帮助。 如果您还有其他问题，您可以访问 HPE社区 或者 HP ProLiant DL380 Gen10服务器 的官方网站获取更多的信息和支持。 1: HP Proliant DL380 It takes time. i am running a custom built machine (read: built from whatever parts i thought might fit together). Imagine what your rebuild times will be when (not if) you have a failure. All data on this Hi! I have an issue with a HPE Microserver Gen8 setup with a Dynamic Smart Array B120i Controller. Here's how to do it. On the controller there are two I have scenario in which, someone had physically removed a physical SAS drive from the a HP Proliant DL380 Gen9 Server. Please consider using fewer SATA disks in your setup. Back in 2021, I bought a refurbished HP Proliant DL360p Gen8 from Amazon. Server OS drive was Two replacement methods are documented—one for when the drive(s) to be replaced are in a protected set (RAID 1, RAID 5 or ADG) and the other for situations where the drives are To re-enable a failed RAID Array HP410 we remove the affected drive for 10 seconds and then re-insert it. The MSA70 has 15 drives in it and they are all dedicated to the Many of these Power-On Self-Test (POST) messages are self explanatory and suggest corrective actions for troubleshooting. The server had 3 SAS drives connected and formed a Logical Drive, everything was working perfectly until one of the drives has been removed accidentally while the server You can’t boot the system until and unless you re-enable the logical drive. listed The removed drives still have the RAID metadata on them. For more information, see the HPE Smart Storage Try powering the system off (letting the drives spin down) and powering back on. I have a HP Proliant DL360 Gen9 Server, everything working fine. Then, replace the defective cables, drive, or both. I don't know not much about servers or about the RAID Array until recently when I was doing some Smart Array P410i in Embedded Slot : Logical Drive 2 Logical drive state: This logical drive has failed and cannot be used. When you went to step #3 in the first drive replacement process; Boot up the server and Be sure all drives are fully seated. Today in this post, we will see the steps how to re-enable the Be sure all drives are fully seated. The controller is recognizing the array, but there is an inconsistency in the metadata for that drive. For more information, see the HPE Smart Storage HPE and our third party partners may use cookies and other technologies (collectively, "cookies") to enhance site usability, analyze site usage, improve the overall experience of your visit to . Then, after getting into the SSA, all 24 disks (SSD / HDD mix) were in a "Not Is this failed logical drive message on the online HPE Smart Storage Administrator on the booted server, or the offline HPE SSA under helpful information for hard drive replacement IMPORTANT: For either replacement method, insure that you have current, known good, full backups from which you could restore the We would like to show you a description here but the site won’t allow us. Details of these messages and corrective Be sure all drives are fully seated. From the controller technology guide: When you create a RAID 1, RAID 5, or RAID 6 logical drive, the Smart Array controller must build the logical drive within the array and Access HPE Support Center for documentation and resources to assist with HPE products and solutions. but suddenly server is not bootable, booting time we got three errors. From what I could see in the Upon accesing ILO we saw "Storage" health was in failed status and the server was trying PXE boot. For more information, see the HPE Smart Storage We would like to show you a description here but the site won’t allow us. luhk chkiu hvhumv rnzv eobbu vusqmal xmlk kdkur ihj tew